Ships direct from 135+ manufacturers and warehouses · No warehouse overhead · Nationwide delivery Mon–Fri 8am–6pm ET · (732) 479-6550

Commercial Sinks & Plumbing

Commercial Sinks: 3-Compartment, Hand & Prep Sink Prices (2026)

By Equipment Specialist Team Last reviewed Prices: typical ranges for new equipment, U.S. 2026

A new commercial three-compartment sink with drainboards typically costs $500–$3,000 in 2026, a wall-mount hand sink $100–$600, and a one- or two-compartment prep sink $200–$1,300, before freight, tax and plumbing. Bowl size, steel gauge, 304 vs. 430 stainless and drainboard length drive most of the difference.

Sinks are the equipment most closely tied to health inspections. Under the FDA Food Code, which most U.S. health departments adopt (often with local amendments), a kitchen that washes utensils by hand needs a sink with at least three compartments, separate handwashing sinks, and drainboards or racks for soiled and clean items. Getting the sink plan right before the plumber arrives avoids expensive rework and failed opening inspections.

Commercial Sinks & Plumbing: types and specs

Add what you need to your quote list. Your specialist confirms exact models, utilities and lead times before quoting. Everything ships direct to you from the manufacturer or its distribution warehouse.

Hand sinks

Dedicated handwashing sinks. The Food Code requires them to be conveniently located and used for no other purpose.

  • Wall-mount, drop-in or pedestal styles
  • Common bowls about 10×14 to 14×16 in.
  • Optional side splashes, knee, foot or sensor valves
  • Food Code 5-202.12: able to supply water at least 100°F (38°C)

One-compartment sinks

Single-bowl sinks for prep, filling stockpots or a dedicated task, with or without drainboards.

  • Bowls about 16×20 to 24×24 in.
  • Bowl depths about 12–14 in.
  • 16 or 18 gauge, 304 or 430
  • Left, right or two drainboards

Two-compartment sinks

Two-bowl sinks for prep, produce washing and thawing; not a substitute for a three-compartment warewashing sink.

  • Bowls about 16×20 to 24×24 in. each
  • Bowl depths about 12–14 in.
  • Optional one or two drainboards
  • Faucet splash-mount or deck-mount

Three-compartment sinks

The standard manual warewashing sink for wash, rinse and sanitize steps.

  • Food Code 4-301.12(A): at least 3 compartments for manual warewashing
  • Compartments large enough to immerse the largest items washed (4-301.12(B))
  • Common bowls 10×14 to 24×24 in., depths 12–14 in.
  • Drainboards on one or both sides (4-301.13)

Mop / service sinks

Low floor basins or stainless service sinks for cleaning mops and disposing of mop water.

  • Food Code 5-203.13 requires at least one service sink or curbed cleaning facility with a floor drain
  • Floor basins often about 24×24 or 24×36 in.
  • Molded stone, terrazzo or stainless
  • Pair with a service faucet and vacuum breaker

Prep sinks

Sinks dedicated to food preparation such as washing produce, kept separate from warewashing and handwashing.

  • One or two compartments
  • Often installed with an indirect (air-gap) drain where required by local code
  • Bowls about 16×20 to 20×28 in.
  • Drainboards for landing produce

Underbar sinks

Modular bar sinks for glass washing, dump sinks and rinse stations under the bar top.

  • Three- or four-compartment glass-wash sinks
  • Bowls about 10×14 in., depths about 10 in.
  • Widths commonly about 36–96 in. with drainboards
  • Match underbar depth (about 18–21 in.) and height

Commercial faucets

Splash-mount and deck-mount faucets built for constant commercial use.

  • Splash-mount centers commonly 8 in.; deck-mount commonly 4 or 8 in.
  • Swing spouts about 6–18 in.
  • Lead-free brass bodies
  • Check flow rate and local plumbing code

Pre-rinse assemblies

Spring-loaded spray valves with an add-on faucet option, mounted at the soiled dish table.

  • Splash-mount or deck-mount
  • Federal DOE efficiency standards apply to pre-rinse spray valves
  • EPA WaterSense labels models at 1.28 gpm or less
  • Wall bracket recommended for stability

Drainboards

Sloped landing areas on sinks for soiled and clean items, or add-on boards to extend capacity.

  • Food Code 4-301.13: drainboards or racks for soiled and clean items
  • Common lengths about 12–36 in.
  • Integral or bolt-on
  • Slope back toward the sink bowl

Grease traps / interceptors

Devices that capture fats, oils and grease before they enter the sewer. Sizing and type are set by the local plumbing code and pretreatment authority.

  • Hydromechanical interceptors (often tested to PDI-G101 or ASME A112.14.3)
  • Gravity interceptors are larger, usually in-ground
  • Flow rating in gallons per minute
  • Confirm required type and size with local code officials

Commercial Sinks & Plumbing prices by type (2026)

TypeBest forTypical price (new)
Hand sink, wall-mount, with faucetEvery kitchen and bar station$100–$600
Hand sink with knee, foot or sensor valveHands-free handwashing$300–$1,200
One-compartment sinkPrep, filling, small tasks$200–$800
Two-compartment sinkProduce prep, thawing$350–$1,300
Three-compartment sink with drainboardsManual warewashing (wash, rinse, sanitize)$500–$3,000
Mop / service sink (floor or stainless)Mop water disposal and cleaning tools$150–$1,000
Underbar sinkBars: glass washing and dump sinks$400–$1,500
Commercial faucetSinks of all types$80–$400
Pre-rinse spray assemblyDish areas ahead of the dishmachine$200–$700
Add-on drainboardExtending soiled or clean landing space$100–$400
Hydromechanical grease interceptor (under-sink / small)Small kitchens where local code allows$300–$2,500
Typical 2026 U.S. street prices for new equipment before freight, installation and tax. Your quote may be higher or lower depending on brand, options and availability.
Common three-compartment sink bowl sizes (inside bowl, front-to-back × left-to-right; check the manufacturer's spec sheet)
Bowl size (in.)Typical bowl depthBest for
10×1410–12 in.Bars, coffee shops, very small menus
16×2012 in.Small cafés and food trucks with limited space
18×1811–12 in.Small to mid-size kitchens
18×2412–14 in.Most full-service restaurants; full-size hotel pans and most pots
20×2812–14 in.High-volume kitchens, larger pots
24×2412–14 in.Bakeries and kitchens washing stockpots and large pans

How to size commercial sinks & plumbing

  • Size three-compartment bowls to fit the largest pan, pot or utensil you wash by hand; the Food Code requires compartments large enough to immerse the largest equipment and utensils (4-301.12(B)).
  • Place hand sinks so every food prep, food dispensing and warewashing area has one conveniently located (Food Code 5-204.11).
  • Plan drainboards or racks on both the soiled and clean sides of the warewashing sink (Food Code 4-301.13).
  • Grease interceptor size and type are governed by your local plumbing code (often based on the UPC or IPC, with PDI-G101 or ASME A112.14.3 for hydromechanical units) and your local pretreatment authority; get their sizing requirement before ordering.
  • Local health departments adopt and amend the Food Code, so confirm sink counts, sizes and placement with your local authority during plan review.

What drives the price

  • Number and size of bowls
  • Gauge and 304 vs. 430 stainless
  • Drainboard length and one vs. two boards
  • Faucets, pre-rinse units and drain fittings (often sold separately)
  • Hands-free valves on hand sinks
  • Grease interceptor type and size
  • Plumbing labor and permits (not included in equipment price)

Energy savings: Commercial pre-rinse spray valves are covered by federal DOE efficiency standards, and EPA WaterSense labels models that use 1.28 gallons per minute or less; check epa.gov/watersense and your water utility for rebates. ENERGY STAR commercial food service equipment.

Before you buy: checklist

  • Confirm whether faucets, drains and legs are included or sold separately.
  • Choose 304 stainless for sinks where possible; constant water, salt and sanitizer are hard on 430.
  • Check NSF/ANSI 2 certification for food-contact sinks.
  • Plan faucet reach so water lands in the center of each bowl.
  • Ask your plumber and local code official about indirect drains, air gaps and backflow requirements before ordering.
  • Hand sinks must be used only for handwashing (Food Code 5-205.11); stock them with soap and hand drying supplies.
  • Confirm everything with your local health department, which adopts and may amend the FDA Food Code.

Commercial Sinks & Plumbing brands we quote

Don't see your brand? We quote most major foodservice manufacturers. Name the brand and model in your quote request.

Get commercial sinks & plumbing quotes

Send us your specs, or just your menu and space, and we'll recommend the right models across brands with a written, freight-included quote.

Get a Free Quote Call (732) 479-6550

Frequently asked questions

How much does a commercial three-compartment sink cost?

A new three-compartment sink with drainboards typically costs $500–$3,000 in 2026, before faucets, freight and plumbing. Small 10×14 in. bar-size units sit at the low end; 16-gauge 304 sinks with large bowls and two long drainboards sit at the high end.

Does a restaurant need a three-compartment sink?

Under the FDA Food Code, a kitchen that washes and sanitizes utensils by hand needs a sink with at least three compartments (section 4-301.12). Some jurisdictions have their own variations, so confirm with your local health department.

How big should three-compartment sink bowls be?

The Food Code requires compartments large enough to immerse the largest equipment and utensils you wash by hand, rather than a fixed dimension. Many full-service kitchens choose 18×24 in. bowls about 12–14 in. deep; check what size your local health department expects.

Can I wash dishes or food in a hand sink?

No. The Food Code requires handwashing sinks to be used for no other purpose than handwashing (section 5-205.11), and they must be conveniently located for employees (section 5-204.11).

What size grease trap do I need?

Grease trap or interceptor size is set by your local plumbing code and local pretreatment authority, not by a single national rule. Many codes are based on the UPC or IPC and reference PDI-G101 or ASME A112.14.3 for hydromechanical units, so ask your plumber and local officials for the required sizing before ordering.

Related guides

Sources

Need help selecting equipment for your kitchen? Request a personalized equipment quote or call (732) 479-6550.

Call a Specialist Get a Free Quote