Ships direct from 135+ manufacturers and warehouses · No warehouse overhead · Nationwide delivery Mon–Fri 8am–6pm ET · (732) 479-6550

Buying guide

304 vs 430 Stainless Steel for Restaurant Equipment

By Equipment Specialist Team Last reviewed

Who this is for: Buyers comparing stainless steel work tables, sinks, shelving and equipment stands.

Short answer: Type 304 stainless contains roughly 18% chromium and 8% nickel, which gives it noticeably better corrosion resistance than type 430, a nickel-free ferritic grade with roughly 16 to 18% chromium. Use 304 anywhere that is wet, salty, acidic or cleaned often with chemicals, such as sinks, prep tables and dish areas. Type 430 is a reasonable, lower-cost choice for dry, light-duty uses.

What is in each grade

All stainless steels rely on chromium, which forms a thin, self-healing oxide film (the "passive layer") on the surface. Type 304 is an austenitic stainless steel, nominally about 18 to 20% chromium and 8 to 10.5% nickel, which is why it is often called 18/8. The nickel stabilizes its structure and improves resistance to many corrosive conditions. Type 430 is a ferritic stainless steel, nominally about 16 to 18% chromium with little or no nickel.

Nickel is the main reason 304 costs more. The price difference between the two grades moves with the nickel market, so it is not a fixed percentage.

PropertyType 304Type 430
FamilyAusteniticFerritic
Chromium (approx.)18–20%16–18%
Nickel (approx.)8–10.5%Little or none
Magnetic?Generally not (annealed); can be slightly magnetic where cold-workedYes
Corrosion resistanceBetterModerate
Relative costHigherLower
Nominal composition and properties. Exact ranges are set by the applicable material specification.

Corrosion: where the difference shows up

In a dry storeroom both grades can look the same for years. The difference appears with moisture, salt, acidic foods (tomatoes, citrus, vinegar, brines), and chlorine-based cleaners and sanitizers. In those conditions 430 is more likely to show rust spots, staining and pitting, while 304 holds up better.

Neither grade is immune. Chlorides, including salt and bleach, can attack both, especially when left to sit or dry on the surface. For very harsh conditions, such as seafood processing or heavy brining, some operators specify type 316, which adds molybdenum for extra chloride resistance at higher cost.

Most "rust" on stainless in a kitchen is surface contamination: iron particles from steel wool or carbon steel tools, or residue from cleaners. Using non-abrasive pads, rinsing off chemicals, wiping with the grain and drying surfaces helps preserve the passive layer on either grade.

Magnetism: a rough screen, not a proof

Type 430 is magnetic. Type 304 is generally non-magnetic in its annealed state, but bending, forming and welding can make parts of a 304 table slightly magnetic. A magnet that sticks strongly to a flat top suggests a ferritic grade such as 430; a weak pull near a bend does not prove a part is not 304. Treat the magnet test as a quick check and rely on the manufacturer's specification and markings for certainty.

Where each grade makes sense

Choose by environment and by how the item is cleaned, not by price alone. Replacing a rusted table costs more than buying the right grade once.

Item / locationSuggested gradeWhy
Compartment sinks, hand sinks, prep sinks304Constant water and chemical exposure
Dish tables and dish-area shelving304Wet, hot and chemical-heavy
Prep tables for produce, proteins, sauces304Acids, salt and frequent sanitizing
Equipment stands near fryers and grills304 preferredGrease and heavy cleaning
Dry storage tables and packing stations430 is fineLittle moisture or chemical exposure
Wall shelves in dry areas430 is fineLow corrosion risk
Walk-in cooler shelvingAsk about coated or polymer optionsCondensation can affect bare steel
General guidance for commercial kitchens. Your cleaning chemicals and menu may change the answer.

Read the whole specification

Listings that say "stainless steel" without a grade, or that give a grade only for the top, are common. Many tables pair a 304 top with a 430 or galvanized undershelf and legs. That can be a sensible way to save money, but you should know what you are buying. Ask for the grade and gauge of the top, undershelf, legs and backsplash.

Grade and thickness are separate choices: an 18-gauge 304 top resists corrosion well but dents more easily than a 14-gauge 430 top. Our work table gauge guide covers thickness.

Assumptions and limitations

Composition figures are nominal ranges commonly published for these grades; the governing material specification and the manufacturer's data control. Corrosion behavior depends heavily on cleaning practices, chemical concentrations and how long surfaces stay wet. This guide is general information, not a materials engineering recommendation, and it is based on published specifications rather than our own testing.

Need help selecting equipment for your kitchen?

Request a personalized equipment quote. Our in-house sales team replies within one business day with freight-included pricing on new equipment from 135+ manufacturers and warehouses.

Get a Free Quote Call (732) 479-6550

Frequently asked questions

Is 430 stainless steel food safe?

Type 430 is widely used in foodservice equipment, and items made with it can be listed to NSF/ANSI food equipment standards. The question is durability: it corrodes more readily than 304 in wet, salty or acidic conditions.

How can I tell 304 from 430 stainless?

A magnet sticks firmly to 430 and usually only weakly or not at all to 304, though formed or welded areas of 304 can be slightly magnetic. The reliable way is the manufacturer's spec sheet or markings.

Why does my stainless table have rust spots?

Often it is surface contamination from steel wool, carbon steel tools or chemical residue, or chloride attack from salt or bleach. Clean with non-abrasive pads, rinse chemicals off and dry the surface. Persistent rust on a wet-area table may mean the grade is not suited to the location.

Is 304 worth the extra cost?

For sinks, dish areas and wet prep, usually yes. For dry storage and light-duty tables, 430 can be a reasonable way to save money.

Sources

Related

This guide is general information for planning and purchasing, not legal, engineering or code-compliance advice. Codes and their adopted editions vary by state and locality; confirm requirements with your health department, building official and licensed installers. Last reviewed on the date shown above.

Call a Specialist Get a Free Quote