Buying guide
Natural Gas vs Propane Restaurant Equipment: What to Order
Who this is for: Restaurant owners, food truck operators and contractors ordering gas ranges, fryers, griddles and ovens.
Short answer: Natural gas and propane equipment are built differently: propane needs smaller burner orifices and a regulator set to a higher manifold pressure, and some models change other parts as well. Order equipment for the gas you actually have, or have it converted with the manufacturer's kit by a qualified technician. Running an appliance on the wrong gas can cause poor performance, sooting, carbon monoxide or fire, and installation should always be done by a licensed gas installer.
How the two fuels differ
Natural gas is mostly methane delivered by a utility pipeline. Propane (liquefied petroleum gas, LP) is stored as a liquid in a tank and delivered by a supplier. Propane carries far more energy per cubic foot than natural gas, so an appliance needs much less of it by volume to produce the same heat. That is why the two fuels need different orifice sizes and pressures.
| Natural gas | Propane (LP) | |
|---|---|---|
| Supply | Utility pipeline and meter | On-site tank or cylinders |
| Approx. heating value | about 1,000 BTU per cubic foot | about 2,500 BTU per cubic foot |
| Burner orifices | Larger | Smaller |
| Manifold pressure | Lower (per data plate) | Higher (per data plate) |
| Leak behavior | Lighter than air, tends to rise | Heavier than air, collects in low areas |
What changes when equipment is converted
Every gas appliance has a data plate that states the gas type it is set up for, its BTU input and its required manifold pressure. Converting between natural gas and propane typically involves changing the burner orifices (and pilot orifices, where present), adjusting or changing the gas regulator, and sometimes adjusting air shutters or replacing valve components. Some manufacturers ship conversion kits with the unit; others sell them separately; some models must be ordered in the correct gas from the factory.
Always use the manufacturer's conversion kit and instructions, have the conversion done by a qualified technician, and make sure the data plate or a conversion label reflects the new gas type. Manufacturers may limit warranty coverage when conversions are done incorrectly or by unqualified people, so check the warranty terms.
BTU ratings and supply planning
BTU input ratings tell you how much gas an appliance uses at full fire. When an appliance is correctly converted, its rated input on propane is usually the same as or close to its natural gas rating, but check the spec sheet because some models list different figures for each gas.
Add up the BTU input of everything on the gas line. Your installer uses that total, the pipe length and the supply pressure to size the gas piping and confirm that the meter (natural gas) or the tank and regulators (propane) can keep up when everything runs at once. Large propane loads in cold climates can also be limited by how fast liquid propane vaporizes in the tank, which your propane supplier should evaluate. At higher elevations, many manufacturers call for adjusted orifices; give the elevation of your site when you order.
Connections, codes and installation
Gas installations are governed by your state and local fuel gas code. Many jurisdictions base theirs on NFPA 54 (National Fuel Gas Code) or the International Fuel Gas Code, and propane storage and handling is commonly governed by NFPA 58. Commercial cooking operations under a hood also fall under ventilation and fire protection rules such as NFPA 96, plus local mechanical and fire codes.
Hire a licensed gas fitter or plumber, pull the required permits, and expect a pressure or leak test and an inspection. Equipment on casters needs a commercial flexible connector designed for movable appliances, typically with a quick-disconnect fitting and a restraining device so the appliance cannot be pulled far enough to stress the connector. Each appliance should have an accessible manual shutoff valve. The installer should verify manifold pressure and burner operation at startup.
Ordering checklist
Before you order gas equipment, confirm: the gas type at the building (natural gas or propane); the elevation if you are at higher altitude; the total BTU load of all appliances; whether each model ships ready for your gas or needs a factory or field conversion; casters versus legs, and the matching connector kit; and any hood or fire-suppression changes the new equipment will require. Tell us the gas type on your quote request and we will confirm the correct configuration with the manufacturer.
Assumptions and limitations
Heating values and pressure relationships are approximate and for orientation only; the appliance data plate and installation manual govern. We do not cite specific code sections because adopted codes and editions vary by jurisdiction. This guide is not installation instructions. Gas work must be done by a licensed professional in accordance with local codes and the manufacturer's instructions.
Need help selecting equipment for your kitchen?
Request a personalized equipment quote. Our in-house sales team replies within one business day with freight-included pricing on new equipment from 135+ manufacturers and warehouses.
Frequently asked questions
Can I use natural gas equipment with propane?
Not without converting it. Propane requires different orifices and regulator settings. Use the manufacturer's conversion kit, installed by a qualified technician, or order the unit for propane from the factory.
Is propane or natural gas cheaper for a restaurant?
It depends on local utility and propane prices. Compare on cost per BTU (or per therm) using quotes from your utility and propane supplier, not on cost per gallon or per cubic foot.
Do propane fryers and ranges have the same BTU rating as natural gas models?
Usually the rated input is the same or close once correctly converted, but some spec sheets list different figures by gas type. Check the model's spec sheet.
Who should convert or install gas equipment?
A licensed gas fitter or plumber, following the manufacturer's instructions and local codes, with permits and inspection where required.
Sources
- NFPA 54, National Fuel Gas Code (NFPA)
- NFPA 58, Liquefied Petroleum Gas Code (NFPA)
- NFPA 96, Ventilation Control and Fire Protection of Commercial Cooking Operations (NFPA)
- NSF (standards and certification)
Related
- Commercial ranges
- Commercial fryers
- Kitchen hood CFM calculator
- Commercial kitchen electrical requirements
This guide is general information for planning and purchasing, not legal, engineering or code-compliance advice. Codes and their adopted editions vary by state and locality; confirm requirements with your health department, building official and licensed installers. Last reviewed on the date shown above.